Here

 

 

We've unearthed the article on How to Install a Bathtub Yourself listed below on the net and think it made perfect sense to relate it with you on this page.

Installing a tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a moderately tough task. If the old bathtub is conveniently obtainable, the project can move speedily; if you have to open a wall to remove the old tub and position the new tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will need a helper to move out the old tub and set in the brand-new one. Make sure you have actually certified yourself for the task as well as fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is better to consider employing one prior to you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will help you install a new bath tub in your bathroom if you have actually currently acquired a brand-new bathtub as well as don't need to alter the plan of your previous water supply pipelines.
Your devices and also product checklist ought to comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Preparing for the Installation

To start with, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to prevent pressure on the bath tub.
Fit the versatile faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be suited its last position.

 

 

Removing Old Taps

If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome due to the limited access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.

 

 

Installing the Tub

Utilizing both wooden boards under its feet, place the tub in the called for placement. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the tub till the level reviews degree.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the tub has actually been utilized a minimum of once as this will settle it into its last placement.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Tub

In the location where the bath satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a stiff seal, creating the water to permeate the wall surface in between the bath as well as the tiling, leading to complications with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not think about this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I found that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while exploring the web. Sharing is nice. Helping people is fun. I am grateful for your time. Visit us again soon.

Visit Site